resin cure

Latest Application of Dynamic Torsional Vibration Method in the Studies of Resin Cure

动态扭振法在树脂固化研究中的最新应用

Simulation Approach of Phenolic Resin Cure for Wood Composite Manufacturing

木质复合材用酚醛树脂胶黏剂固化过程的模拟方法

The resin cure experiment results measured by the fiber optic sensor were given .

给出了利用这种传感器进行复合材料固化监测的实验结果。

Monitoring for Residual Strain of Resin Cure During the Process of RTM Composites

RTM工艺成型复合材料树脂固化过程残余应变监测研究

Barium PF resin cure temperature is lower than that of ordinary PF resin .

钡酚醛树脂固化温度比普通酚醛树脂低；

The real time monitoring for residual strain induced by resin cure during the RTM process was realized by measuring the relationship among wave deflection , temperature and curing time .

通过光纤光栅波长偏移与温度和固化时间之间的关系测试，得到了树脂固化过程中残余应变的变化历程，成功实现了RTM工艺树脂固化过程中残余应变的在线监测。

The precure process makes the resin cure to a certain extent , decreases resin flowability , improves resin processability significantly , and enhances the composite laminates quality .

预固化可使氰酸酯树脂发生一定程度的自聚反应，从而降低其流动性，可明显改善氰酸酯树脂的工艺性，提高了层板的成型质量。

The normalized speckle spatial spectrum depended upon the variation of the refractive index occurred through the resin cure process was calculated , the approximate relation between refractive index and cutoff frequency was given .

计算了随着在树脂固化过程中折射率变化的功率谱密度分布，给出截止频率与折射率的近似关系。

The cure kinetics model is based on Kamal 's model , and the degree of the resin cure as a function of temperature and time . This improved mixing dielectric model yields an excellent fit to measured data .

树脂的固化模型利用了Kamal提出的固化动力学方程，将固化度取为时间和温度的函数。

Study progress in shrinkage control of low profile unsaturated polyester resin during cure

国外低轮廓UPR固化收缩控制研究发展动态

Effect of Brominated Phenolic Resin on Cure Characteristics of EPDM

溴化酚醛树脂对EPDM胶料硫化特性的影响

S : Performance and composition of ambient cure fluoropolymer paint applied on antenna of printed board are introduced . Influence of fluoropolymer resin , cure r and additives to film performance is emphasized .

介绍了印制版天线用氟碳涂料的性能要求及其组成，重点讨论了氟碳树脂、固化剂和助剂对涂膜性能的影响，并用红外光谱手段对氟碳涂料的常温固化进行了跟踪。

A Process Simulation of Resin Flow and Cure during Resin Film Infusion Process

RFI工艺中树脂流动行为和固化过程分析

Hydroxymethyl bisphenol A epoxy Resin RT rapid Cure adhesive

羟甲基双酚A环氧树脂室温快速固化粘合剂

The results show that the novel resin has a cure shrinkage lower than that of typical epoxies in room temperature ;

结果表明，这类新型树脂在室温下，固化收缩小于环氧树脂。

And the influence of the functionality of the isocyanate prepolymer and the resin blend on cure speed , cure efficiency and film properties .

异氰酸酯和胺组分官能对凝胶时间、固化效率和聚脲涂层性能的影响。

Cure Behavior of Thermosetting Resins Studied by the Dynamic Torsional Vibration Method-Application of LHX-I Resin Curemeter in Cure Study of Thermosetting Resins and Resin-based Composites

研究热固性树脂固化的动态扭振法&LHX-I型树脂固化仪在热固性树脂和树脂基复合材料固化研究中的应用

A study was made on the EAM resin gel property and cure property by DSC and IR .

本文研究了EAM树脂的凝胶特性，用DSC、IR研究了树脂的固化特性。

The DSC analysis discovers that the modification of PF resin with hard resin cure faster than general PF .

DSC分析发现紫胶硬树脂改性酚醛树脂的放热反应温度更低一些。

In this Nper , N-p-carboxylphenylmaleimide ( P-CPMI ) was synthesized and the curing reaction of o-cresol formaldehyde epoxy resin with it as cure agent was investigated .

合成了N-对羧基苯基马来酰亚胺，并将其用作邻甲酚醛环氧树脂的固化剂。

Whether the wrapped products to obtain the ideal design strength , It not only depended on material itself performance and the proportion of fiber and resin , but also had an important relations with the resin cure process .

缠绕制品能否获得理想的设计强度，不仅与材料本身的性能以及纤维树脂的比例有关，而且与树脂的固化过程有着重要的关系。